Grandfather's 68 SS Camaro.

[JRC99]

Originally Posted by Too Many Projects

Does the NOS cam have original packaging with a date produced on it ? If it's from the 80's or 90's, one would think it was a better quality product back then.

I can say with confidence it has the old Competition Cams box instead of the reds and white COMP logo.

I hope links to it are okay (and please, y'all, don't snipe this from me ��)
1
https://www.ebay.com/itm/12553460773...cAAOSwGcNjM2el

[Too Many Projects]

Says it sold at 5:06 pm.... sorry.

[JRC99]

Originally Posted by Too Many Projects

Says it sold at 5:06 pm.... sorry.

That's because it was me lol

I still have to finish tearing it down and get the machine work done, but buying the cam was a big hurdle. I'm glad I hesitated to order one before verifying the grind because I'd have been very, very unhappy to end up buying the wrong one on accident.

[Too Many Projects]

Cool... now you need to find out what is the best lifter to buy. I've read about one that has a small oil hole in the bottom to lube the lobe directly.
Time to pull that engine down to the bare block and start cleaning all the metal particles out.

[JRC99]

Originally Posted by Too Many Projects

Cool... now you need to find out what is the best lifter to buy. I've read about one that has a small oil hole in the bottom to lube the lobe directly.
Time to pull that engine down to the bare block and start cleaning all the metal particles out.

My buddy, who's got plenty of experience with flat tappets, swears by Isky*. So I'll be getting a set of those when it's actually time to put it together. I'm not too sure when I'll rip it down the rest of the way- being a TFT at Ford means my employment is slightly up in the air, and if it wasn't for the perfect timing of an NOS cam of the same grind popping up as soon as I found out what's in it, I wouldn't have bought it. Unfortunately, as is all too common in life, I need to save up for a bit.

Sure, I could tear it down anyway, and I may even do that. I just have concerns I'll lose something critical having it all torn down for ages.

*These specifically look like a safe bet as long as I make sure the lifter bores are right. I'm merely thinking here, but I'd really like to have the cam broken in on a run stand, too, instead of in the car. https://www.summitracing.com/parts/isk-202-hy

[Too Many Projects]

If you don't see getting it hot tanked and flushed good for reassembly soon, don't take it apart... If I recall, you got a good stand for it ? I would pull the pan and start removing main caps to inspect for shaving damage to the crank and then put them back for now. If the crank is ground up, you know you'll be looking at regrinding at the very least, or replacement. If the mains look good, inspect the rod journals. Get as much inspection work done now, to know what you are facing for parts and cost. Just put everything back for now so nothing gets misplaced.

[JRC99]

Originally Posted by Too Many Projects

If you don't see getting it hot tanked and flushed good for reassembly soon, don't take it apart... If I recall, you got a good stand for it ? I would pull the pan and start removing main caps to inspect for shaving damage to the crank and then put them back for now. If the crank is ground up, you know you'll be looking at regrinding at the very least, or replacement. If the mains look good, inspect the rod journals. Get as much inspection work done now, to know what you are facing for parts and cost. Just put everything back for now so nothing gets misplaced.

Pan is off (and very glittery as you all fully called- I'll own that one. I'm very thankful I decided to listen to those who have been there and done that). I'm about to have a week and a half off for Christmas so I'll probably take your advice and tinker here and there.