Dedicated to the Promotion and Preservation of American Muscle Cars, Dealer built Supercars and COPO cars. |
|
#1
10-31-2022, 10:16 PM
|
||||
|
||||
Stencil Kits
We’re getting closer to paint on the 67 Z. Does anyone have a recommendation on a stencil kit for the stripes?
Thanks Paul 
|
|
#2
10-31-2022, 10:39 PM
|
||||
|
||||
|
|
|
#5
10-31-2022, 11:22 PM
|
||||
|
||||
|
Stencils & Stripes Is who I've used with good success....Joe
__________________
1968 Z/28 Corvette Bronze. Black Hounds Tooth. 02E Los Angeles born 3/13/1968 pnt OO 1969 SS396 Yellow/Yellow 08E Norwood born 8/28/1969 pnt 76E 1970 'cuda Moulin Rouge, 440-6, 4 speed
|
| The Following User Says Thank You to X66 714 For This Useful Post: | ||
juliosz (10-31-2022) | ||
|
#6
10-31-2022, 11:33 PM
|
||||
|
||||
|
Like Joe, I would recommend Stencils & Stripes in Illinois. I bought their kit for my 69 Z/28 and it was identical to all the original tracings I took from the car's original paint marks. Excellent templates in my opinion.
https://www.stencilsandstripes.com/p.../model/camaro/
__________________
I like solid lifter cars, big cams and cars w/ 3 pedals in them. 
|
| The Following 3 Users Say Thank You to NorCam For This Useful Post: | ||
|
#7
10-31-2022, 11:56 PM
|
||||
|
||||
|
Quote:
|
| The Following 9 Users Say Thank You to juliosz For This Useful Post: | ||
169indy (11-01-2022), 1967Z28 (11-04-2022), Lee Stewart (11-01-2022), napa68 (11-01-2022), NorCam (11-01-2022), olredalert (11-01-2022), PeteLeathersac (11-04-2022), RPOLS3 (11-01-2022), X66 714 (11-01-2022) | ||
|
#8
11-01-2022, 02:37 AM
|
|||
|
|||
|
That is who I used for the stencil kit on my 69 Z, and like Norcam said, it was dead on.
__________________
Don't believe everything you read on the internet ... Ben Franklin
|
| The Following User Says Thank You to Lynn For This Useful Post: | ||
juliosz (11-01-2022) | ||
|
#9
11-04-2022, 12:18 PM
|
||||
|
||||
|
I have a kit on order from Stencils and Stripes. Many thanks for all of the advice and support from the fine folks on this forum!
|
| The Following User Says Thank You to juliosz For This Useful Post: | ||
X66 714 (11-04-2022) | ||
|
#10
11-04-2022, 05:03 PM
|
||||
|
||||
|
The '67-'68 is obviously a little different in the back compared to a '69. I had a Stencils & Stripes kit and found I had to fudge around a little to get it to look accurate and how I wanted it. I did have an original paint '67 Z trunk lid to help get the spacing right. I mounted that lid and masked the filler panel below the rear window and then mounted the lid I was going to use. I then masked that lid following what was above. The original stripes are slightly narrower at the back edge than up toward the window if I remember correctly.
Last edited by 1967Z28; 11-04-2022 at 08:18 PM.
|
 |
|
|
Linear Mode
