Go Back   The Supercar Registry > General Discussion > Technical & Restoration


Reply
 
Thread Tools Display Modes
  #1  
Old 08-14-2011, 07:06 PM
COPO PETE COPO PETE is offline
Senior Member
 
Join Date: Apr 2001
Location: Glencoe, Ont. Canada.
Posts: 1,382
Thanks: 0
Thanked 0 Times in 0 Posts
Default Re: COPO Chevelle start/run problems

Thanks for the reply guys. I'll check out the wiring tomorrow. I did put a different switch on the column, but had the same results. But..... if that wire is burned out (resister) why would it run in the "start" position, but no the "run" position????
Peter
Reply With Quote
  #2  
Old 08-14-2011, 07:16 PM
John Brown's Avatar
John Brown John Brown is offline
Yenko Contributing Member
 
Join Date: Mar 2002
Location: South Bend, Indiana
Posts: 2,820
Thanks: 455
Thanked 511 Times in 243 Posts
Default Re: COPO Chevelle start/run problems

The little yellow wire that runs from the solenoid powers the ignition when the key and switch are in the start position. When you release the key, you would be running on the normal ignition switch and the resistor wire running through the rest of the harness. If the ignition switch or the resistor wire is at fault, it could start or run in the start position, but not in the run position.
__________________
......................
John Brown

This isn't rocket surgery.....
Reply With Quote
  #3  
Old 08-14-2011, 07:46 PM
bwag bwag is offline
Yenko Contributing Member
 
Join Date: Jan 2004
Location: NW Ohio
Posts: 166
Thanks: 6
Thanked 52 Times in 18 Posts
Default Re: COPO Chevelle start/run problems

When troubleshooting a no run condition , I always start with a test light at the coil + terminal. With the ignition in RUN position there should be 12 Volts at the + terminal . If no voltage there go to the 12 ga purple wire on the Ign switch and test . If you have power there ,find the open between the two places you just tested . If no power at the switch ,adjust the switch first ,if still no power replace the switch.
Reply With Quote
  #4  
Old 08-14-2011, 08:29 PM
John Brown's Avatar
John Brown John Brown is offline
Yenko Contributing Member
 
Join Date: Mar 2002
Location: South Bend, Indiana
Posts: 2,820
Thanks: 455
Thanked 511 Times in 243 Posts
Default Re: COPO Chevelle start/run problems

Purple wire just energizes the solenoid. It does have to go through the neutral safety switch first though. It doesn't really have anything to do with the actual ignition circuit.
__________________
......................
John Brown

This isn't rocket surgery.....
Reply With Quote
  #5  
Old 08-15-2011, 01:28 AM
napa68's Avatar
napa68 napa68 is offline
SCR Sponsor
 
Join Date: Oct 2008
Location: Presque Isle, WI
Posts: 3,862
Thanks: 5,936
Thanked 5,311 Times in 1,325 Posts
Default Re: COPO Chevelle start/run problems

The power to the ignition is overrode from the starter solenoid. It then gets full battery voltage as opposed to resisted voltage.

Different circut, thus different results.

Tim
Reply With Quote
  #6  
Old 08-16-2011, 01:05 AM
COPO PETE COPO PETE is offline
Senior Member
 
Join Date: Apr 2001
Location: Glencoe, Ont. Canada.
Posts: 1,382
Thanks: 0
Thanked 0 Times in 0 Posts
Default Re: COPO Chevelle start/run problems

Thanks guys. So, ...... + side of coil had 10 volts in the start position, but 0 volts in the run position. Put a wire from + battery direct to + coil and started right up and ran. Looks like the wiring harness (resister wire) is no good as predicted by you folks. New wiring harness on the way!
Thanks to all the responded!
Peter
__________________
Pete Simpson 1962-2013 RIP
Owen Simpson
Eric Simpson
Reply With Quote
  #7  
Old 08-16-2011, 01:24 AM
njsteve's Avatar
njsteve njsteve is offline
Yenko Contributing Member
 
Join Date: Nov 2003
Location: NJUSA
Posts: 8,492
Thanks: 9
Thanked 3,017 Times in 923 Posts
Default Re: COPO Chevelle start/run problems

Happy to hear our combined advice worked. Now I can finally tell my wife that someone, somewhere in the universe followed my advice and achieved success.

[img]<<GRAEMLIN_URL>>/grin.gif[/img]
Reply With Quote
  #8  
Old 08-16-2011, 03:43 PM
SS427's Avatar
SS427 SS427 is offline
Yenko Contributing Member
 
Join Date: Jul 2001
Location: Pleasant Plains, IL
Posts: 10,326
Thanks: 3,164
Thanked 4,581 Times in 1,140 Posts
Default Re: COPO Chevelle start/run problems

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: njsteve</div><div class="ubbcode-body">Now I can finally tell my wife that someone, somewhere in the universe followed my advice and achieved success.

[img]<<GRAEMLIN_URL>>/grin.gif[/img] </div></div>

Doesn't that feel good? It has likely happened many times before, you just didn't know it..... [img]<<GRAEMLIN_URL>>/wink.gif[/img]
__________________
Rick Nelson
Musclecar Restoration and Design, Inc (retired)
www.musclecarrestorationanddesign.com
https://www.youtube.com/watch?v=62r-6vgk2_8
specialized in (only real) LS6 Chevelle restorations
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 03:49 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.

O Garage vBulletin Plugins by Drive Thru Online, Inc.