The Supercar Registry
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

The Supercar Registry (https://www.yenko.net/forum/index.php)
-   Parts/Memorabilia - Wanted (https://www.yenko.net/forum/forumdisplay.php?f=84)
-   -   68-69 Camaro or 68-72 Nova Subframe needed (https://www.yenko.net/forum/showthread.php?t=137616)

Hotrodpaul 05-20-2016 05:49 PM
68-69 Camaro or 68-72 Nova Subframe needed
 
Looking for a nice, straight 68-69 Camaro or Nova front subframe bare or with suspension, for my 69 Z-28 Project X resto.

PM me with details.

Thanks, Paul
832-373-7740

the427king 05-21-2016 07:08 PM
Re: 68-69 Camaro or 68-72 Nova Subframe needed
 
67 WONT WORK?

68moz28rs 05-21-2016 08:57 PM
Re: 68-69 Camaro or 68-72 Nova Subframe needed
 
67 Has different holes in the front of the subframe then 68-9. It would still work though

the427king 05-21-2016 10:11 PM
Re: 68-69 Camaro or 68-72 Nova Subframe needed
 
I believe the very early 67s had no hole,and after that they were all the same..

Woj 05-22-2016 03:03 AM
Re: 68-69 Camaro or 68-72 Nova Subframe needed
 
I would think that shouldn't be too difficult to find one near you. The subframe is good up to '74 Nova as I recall from Hollanders. Some of the off-brands like Buick, Olds, Pontiac had some funky brackets welded on them but the same otherwise.

Good luck.

WorkinProgress 05-22-2016 04:17 AM
Re: 68-69 Camaro or 68-72 Nova Subframe needed
 
'67 frames have the lower A arm bumper attached to the subframe not on the A arm like '68 and '69s. 1968 has the A arm bumper on the backside of A arm. 1969 has the A arm bumper on the front side. 1969 has two subframes. One was used up till around August of 1969 and the revised version after that for the late build '69 Camaros or the 1970 Nova.

- Warren

enio45 05-22-2016 03:58 PM
Re: 68-69 Camaro or 68-72 Nova Subframe needed
 
Warren,

can you tell me more about the differences on the 69 subframes?

WorkinProgress 05-23-2016 04:09 AM
Re: 68-69 Camaro or 68-72 Nova Subframe needed
 
Eddie, the easiest way to tell a late '69 Camaro frame or '70 up Nova is by looking at the driver's side front top three holes. The forward hole is used for the radiator support mounting. The third rearward hole will be elongated on the later frames. From what I was told, but never checked to verify is it was elongated for the vent hose used with the charcoal canister on the Nova.

- Warren

KevinW 05-23-2016 11:13 AM
Re: 68-69 Camaro or 68-72 Nova Subframe needed
 
Paul, talk to this guy in Colorado, maybe you can work something out.

http://www.camaros.net/forums/66-wha...nsion-etc.html

Quote:
Fresh Professionally Built original 68 327 Camaro RS
Engine 327 .030 over, line honed, Maule coated pistons 10:1, Double hump heads, Comp cam, rocker roller and all accessories shown, intake air cleaner, alt, A/C compressor, headers, electronic ignition, starter, wiring harness, etc
Subframe, powder coated, new bushing, bearings, seals, springs
Quick ratio gear box
radiator and shroud
Disc brakes, brake lines, rear drums, master cylinder all new
1961 date coded, T10 four speed, rebuilt, new clutch, aluminum flywheel
(The car was originally an auto)
12 bolt rear 3.73 fresh rebuilt and powder coat
drive shaft
2.5 inch exhaust never installed

What's it worth!

enio45 05-23-2016 02:37 PM
Re: 68-69 Camaro or 68-72 Nova Subframe needed
 
thanks for the info Warren


All times are GMT. The time now is 12:00 PM.
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.


O Garage vBulletin Plugins by Drive Thru Online, Inc.