Forum: Supercar/Musclecar Discussion
09-30-2024, 12:04 AM
|
Replies: 34
Views: 4,345
Order form
I forgot I had this photo. Perhaps this helps?? This is a Baltimore built L89.
Let me know if you need any additional information on the car.
Cheers,
Marty
|
Forum: Ebay & other seen ads section
09-29-2024, 06:49 AM
|
Replies: 10
Views: 1,917
Stamping doesn't line up like the one in this...
Stamping doesn't line up like the one in this thread:
https://www.stevesnovasite.com/threads/66-cowl-tag-breakdown.519889/
Also don't recall seeing any tag with a single Group 1 code that is...
|
Forum: Technical & Restoration
09-27-2024, 01:40 PM
|
Replies: 6
Views: 907
|
Forum: Chevrolet
09-26-2024, 03:20 PM
|
Replies: 441
Views: 297,595
|
Forum: Chevrolet
09-26-2024, 02:47 PM
|
Replies: 441
Views: 297,595
|
Forum: Supercar/Musclecar Discussion
09-26-2024, 12:14 PM
|
Replies: 0
Views: 264
|
Forum: Muscle Car and Corvette Nationals
09-24-2024, 11:51 PM
|
Replies: 2
Views: 548
Registered for MCACN 2024
First time going to this show and will be bringing my Monaco Orange LS6. If your at the show stop by and introduce yourself, would like to meet some of you. Until then.
|
Forum: Supercar/Musclecar Discussion
09-23-2024, 06:41 PM
|
Replies: 62
Views: 35,992
|
Forum: Pontiac
09-23-2024, 03:15 PM
|
Replies: 109
Views: 77,737
|
Forum: Member's Rides
09-21-2024, 11:17 PM
|
Replies: 174
Views: 99,114
More Body work and my thoughts on NOS sheetmetal
This is just a glimpse into the time commitment required for body work. All panels are stripped and dents worked out, followed by filler to smooth out areas. This gets followed by epoxy primer....
|
Forum: Technical & Restoration
09-19-2024, 11:30 AM
|
Replies: 4
Views: 397
For 1969, Chevrolet used revised mounting...
For 1969, Chevrolet used revised mounting components for 302 and 350 engines.
The frame brackets [3945507 & 3945508] were re-designed to accommodate the new interlock motor mount. The new mount...
|
Forum: Member's Rides
09-19-2024, 12:53 AM
|
Replies: 174
Views: 99,114
Engine Paint
Hi Rich,
I have been using the Bill Hirsch stuff for all engine builds i have done. I have used everything from there Hemi orange for some 6 pack engines I built for some other guys as well as...
|
Forum: Member's Rides
09-15-2024, 11:34 PM
|
Replies: 174
Views: 99,114
Black and Orange Painting
Between the last 2 weekends painted some chassis parts along with some engine pieces. Did some rear end factory paint marks.
|
Forum: Day 2 stuff-modified cars
09-09-2024, 09:47 PM
|
Replies: 16
Views: 2,185
|
Forum: Day 2 stuff-modified cars
09-09-2024, 04:16 PM
|
Replies: 16
Views: 2,185
|
Forum: Member's Rides
09-09-2024, 01:04 AM
|
Replies: 174
Views: 99,114
Thanks to some mice
This is one that is a first for me. Upon doing some window channel sand blasting i found the package tray area undeer the dutchman panel was pinholes from rust. After investigating and blowing out...
|
Forum: L78/L89 specific Forum
09-08-2024, 04:07 AM
|
Replies: 400
Views: 244,105
|
Forum: Supercars/Musclecars-Wanted
09-06-2024, 11:36 PM
|
Replies: 52
Views: 26,184
First base Camaro with yellow houndstooth I’ve...
First base Camaro with yellow houndstooth I’ve come across. I’d be surprised if there were double digits of them built - certainly a rare car indeed. A shame it’s not going back to stock however if...
|
Forum: Technical & Restoration
09-04-2024, 06:33 PM
|
Replies: 4
Views: 661
|
Forum: Member's Rides
09-02-2024, 01:31 PM
|
Replies: 174
Views: 99,114
Rough in Complete
After stripping its hammer out the dents, followed by the base layer of filler. I wanna point out that the better job of hammering out the dents the less filler you have which is the primary goal. ...
|
Forum: Member's Rides
09-01-2024, 10:09 AM
|
Replies: 174
Views: 99,114
|
Forum: Yenko Chevrolet
08-28-2024, 01:40 PM
|
Replies: 8
Views: 5,384
Here's an article telling of the Yenko families...
Here's an article telling of the Yenko families beginnings in Bentleyville called Central Garage https://www.eastvalleytribune.com/money/don-yenko/article_ea7f88d5-df37-5ae6-8977-1ebc842b96e7.html
...
|
Forum: Chevrolet
08-27-2024, 06:13 PM
|
Replies: 531
Views: 296,062
...I've met both Chuck and Jose in person and...
...I've met both Chuck and Jose in person and have to say they are really good guys who get it, as most of us do here, and watching both of their 67s be built through the lens of this forum has been...
|
Forum: Camaro Nationals- Morgantown,PA
08-26-2024, 10:51 AM
|
Replies: 6
Views: 1,135
|
Forum: Member's Rides
08-26-2024, 01:25 AM
|
Replies: 174
Views: 99,114
Body Work has started
Ive noticed there are a lot of fancy and quick ways to strip the body. Its a slow process for me. Paint stricer and a super sharp putty knife. Someone caved in the roof at one time so pounding out...
|