Forum: Day 2 stuff-modified cars
Yesterday, 12:53 PM
|
Replies: 153
Views: 109,695
|
Forum: Day 2 stuff-modified cars
Yesterday, 03:17 AM
|
Replies: 37
Views: 14,253
|
Forum: Buick
08-10-2024, 07:37 PM
|
Replies: 135
Views: 74,116
|
Forum: Supercars/Musclecars-For Sale
08-09-2024, 01:57 PM
|
Replies: 11
Views: 972
|
Forum: AMC
08-07-2024, 08:55 PM
|
Replies: 7
Views: 512
And finally here’s where we are today.
Ran to...
And finally here’s where we are today.
Ran to the machine shop and dropped off the pistons, stopped by the other machinist doing the crank to drop off 1 rod with a bearing in it for him to measure...
|
Forum: AMC
08-07-2024, 08:46 PM
|
Replies: 7
Views: 512
So the original plan for the engine was to use...
So the original plan for the engine was to use parts I had laying around to put something together, unfortunately the original 360 block I planned to use was no good(cam bearings were loose) so that...
|
Forum: AMC
08-07-2024, 08:30 PM
|
Replies: 7
Views: 512
So parts started being ordered.
A friend...
So parts started being ordered.
A friend donated a set of 5.13 gears for the Dana 60 and while I was originally hoping to use a factory Dana Sure Grip I picked up that turned out to be no good....
|
Forum: AMC
08-07-2024, 08:02 PM
|
Replies: 7
Views: 512
Street Freak Rambler build
So here’s a new build thread for the forum. Unlike my last 2 this one is more ongoing and is still very far away from any type of completion. So they’ll be a couple of posts bringing it up to speed...
|
Forum: Preservation forum
08-07-2024, 12:02 PM
|
Replies: 266
Views: 119,704
|
Forum: Preservation forum
08-06-2024, 12:20 PM
|
Replies: 266
Views: 119,704
Small updates.
Photos 986 - 987 - Installed...
Small updates.
Photos 986 - 987 - Installed a new ET decal on the diff cover
Photo 988 - Found the photo of the traction bars from when I first purchased them. As you can see they needed a...
|
Forum: Lounge
08-05-2024, 11:25 PM
|
Replies: 29
Views: 2,248
Haha, just came across this post. Apparently I...
Haha, just came across this post. Apparently I just bought an ugly truck. :D I just wanted something different from black or white or silver etc.
Here’s my ugly battleship gray shiny primer (AKA...
|
Forum: Member's Rides
08-05-2024, 12:44 AM
|
Replies: 152
Views: 85,983
Rust Repair
Im about finished working through trunk, and floor patching.
|
Forum: Yenko Chevrolet
08-04-2024, 02:17 AM
|
Replies: 22
Views: 4,747
|
Forum: Pit Area - Racing
07-30-2024, 01:55 PM
|
Replies: 17
Views: 13,180
Worked at Shaw's Speed shop from 1969 to 1971
At that time Bruce Shaw and his better half, Barbra, were running the Willow Grove Store. At that time Shaw's Speed Shops second location was in north Philadelphia. A little bigger store than...
|
Forum: Supercar/Musclecar Discussion
07-27-2024, 04:26 AM
|
Replies: 25
Views: 16,053
|
Forum: Buick
07-26-2024, 04:12 PM
|
Replies: 135
Views: 74,116
|
Forum: Buick
07-26-2024, 04:08 PM
|
Replies: 135
Views: 74,116
,,,,,,,,,,,,
,,,,,,,,,,,,
|
Forum: Day 2 stuff-modified cars
07-26-2024, 02:46 PM
|
Replies: 37
Views: 14,253
We spent some time this week getting this 454...
We spent some time this week getting this 454 ready to run, and did cam break in last night. There's a little more work to do tonight, then I plan to bring it to a car show in Rushford MN tomorrow.
|
Forum: Supercar/Musclecar Discussion
07-23-2024, 06:23 PM
|
Replies: 88
Views: 37,353
|
Forum: Lounge
07-23-2024, 02:20 AM
|
Replies: 39,055
Views: 9,969,704
|
Forum: Yenko Chevrolet
07-22-2024, 11:22 PM
|
Replies: 4
Views: 734
Yenko Turbo Z
Mark Hassett just picked up an addition to his already impressive collection. He ask if I would post a couple pics.
Jamie
|
Forum: Supercar/Musclecar Discussion
07-22-2024, 03:01 AM
|
Replies: 6
Views: 802
|
Forum: Supercar/Musclecar Discussion
07-19-2024, 10:10 PM
|
Replies: 17
Views: 1,739
|
Forum: Lounge
07-19-2024, 06:48 PM
|
Replies: 6
Views: 511
Glory Days drags
Was able to run down to Byron Dragway for a long lunch break today and take in some of the Glory Days event action. Walked through the swap meet, pit area, and watched some racing. Was a nice day...
|
Forum: Technical & Restoration
07-19-2024, 04:27 PM
|
Replies: 9
Views: 574
If you can't work it in, in one piece, I would...
If you can't work it in, in one piece, I would cut it near the back radius that goes over the frame and install as 2 and join the ends with a hose. This is only suction, no pressure, so not a concern...
|