Forum: Lounge
08-12-2024, 02:36 AM
|
Replies: 30
Views: 6,826
|
Forum: Lounge
08-12-2024, 02:30 AM
|
Replies: 30
Views: 6,826
Forgot to mention that I made a mount for the...
Forgot to mention that I made a mount for the battery. Welded in two pieces of angle iron. You can see the burn through, so I know I got good penetration.
Laid a piece of 3/8 plywood on the angle...
|
Forum: Lounge
08-12-2024, 02:24 AM
|
Replies: 30
Views: 6,826
Also mounted a low pressure fuel pump for carb...
Also mounted a low pressure fuel pump for carb applications that will be using electric pumps. It will go on circuit 3. I started to mount it on the outside, but figured it would be safer on the...
|
Forum: Lounge
08-12-2024, 02:21 AM
|
Replies: 30
Views: 6,826
Got the cutouts done for gauges and control...
Got the cutouts done for gauges and control panel. Control panel has a master switch and three accessory switches.
Also has a built in push button for the starter.
Have an extra gauge hole. ...
|
Forum: Lounge
08-12-2024, 02:17 AM
|
Replies: 30
Views: 6,826
Added an overflow system for the coolant. I...
Added an overflow system for the coolant. I already have a coolant recovery tank, but just in case THAT system overflows (I hate getting coolant on the floor) I ran a tube to an old antifreeze jug...
|
Forum: Lounge
08-09-2024, 04:10 PM
|
Replies: 8
Views: 519
|
Forum: Supercar/Musclecar Discussion
08-07-2024, 08:00 PM
|
Replies: 20
Views: 1,777
|
Forum: Ebay & other seen ads section
08-05-2024, 03:24 AM
|
Replies: 7
Views: 2,399
|
Forum: Lounge
08-04-2024, 05:09 PM
|
Replies: 6
Views: 649
|
Forum: Technical & Restoration
08-04-2024, 02:56 AM
|
Replies: 1
Views: 434
|
Forum: Supercar/Musclecar Discussion
08-03-2024, 12:12 PM
|
Replies: 8
Views: 1,092
|
Forum: Auctions
07-31-2024, 08:46 PM
|
Replies: 7
Views: 1,034
|
Forum: Lounge
07-31-2024, 08:34 PM
|
Replies: 38
Views: 2,418
|
Forum: Technical & Restoration
07-30-2024, 09:27 PM
|
Replies: 10
Views: 931
|
Forum: Ebay & other seen ads section
07-24-2024, 11:17 PM
|
Replies: 26
Views: 3,789
|
Forum: Lounge
07-22-2024, 11:25 PM
|
Replies: 39,055
Views: 10,016,724
|
Forum: Chevrolet
07-22-2024, 11:16 PM
|
Replies: 33
Views: 2,482
Mitch; you rat bastard. I was reading through...
Mitch; you rat bastard. I was reading through Tim's post and was planning on an almost identical response .... except I was going to offer free storage for this red Corvette. Sherri loves the mid...
|
Forum: Ebay & other seen ads section
07-18-2024, 12:07 AM
|
Replies: 26
Views: 3,789
|
Forum: Supercar/Musclecar Discussion
07-15-2024, 09:30 PM
|
Replies: 13
Views: 2,178
|
Forum: Ebay & other seen ads section
07-13-2024, 09:31 PM
|
Replies: 7
Views: 953
|
Forum: Lounge
07-09-2024, 09:55 PM
|
Replies: 14
Views: 1,329
|
Forum: Lounge
07-08-2024, 01:27 AM
|
Replies: 30
Views: 6,826
The framework for the dash panel has brackets...
The framework for the dash panel has brackets welded on both sides. I think that makes a great place to mount a throttle control.
Haven't had a lot of time to spend on this, but pleased with the...
|
Forum: Lounge
07-08-2024, 01:20 AM
|
Replies: 30
Views: 6,826
|
Forum: Lounge
07-08-2024, 01:19 AM
|
Replies: 30
Views: 6,826
I was thinking that I would make some gizmo to...
I was thinking that I would make some gizmo to retain the prop rods stored in the straight up position; then saw that they hit nothing and were out of the way hanging straight down. So, I just let...
|
Forum: Lounge
07-08-2024, 01:17 AM
|
Replies: 30
Views: 6,826
Here is the panel and frame assembly for the...
Here is the panel and frame assembly for the dash. Cut down a couple of small gate hinges, drilled an extra hole in each and attached it to the radiator support.
Cut some 5/8 rebar to length for...
|