Harry Mann 68 L78 / L88 Camaro - Page 27

**WILMASBOYL78** · #**261** 11-25-2022, 03:53 PM

Nice job on getting the front end pieces cleaned...looks great.

?? How does that Mark Ten unit work, I have seen these before, but not really up to speed on how they work.

-wilma

**TimG** · #**262** 11-25-2022, 06:13 PM

That looks great, Tim.

**napa68** · #**263** 11-25-2022, 06:37 PM

Quote:

Originally Posted by WILMASBOYL78

Nice job on getting the front end pieces cleaned...looks great.

?? How does that Mark Ten unit work, I have seen these before, but not really up to speed on how they work.

-wilma

It's a transistorized amplifier of sort. There was one on the car from way back. This one is installed as a dummy of you will. The car actually has a MSD box hidden under the dash.

Tim

**dykstra** · #**264** 11-26-2022, 02:09 AM

Looks great Tim!!

**napa68** · #**265** 12-12-2022, 09:02 PM

Off to see the wizard tomorrow

**dykstra** · #**266** 12-12-2022, 10:13 PM

Awesome!! Can’t wait to hear the bad assery!!!!

**Too Many Projects** · #**267** 12-12-2022, 10:44 PM

I see you have your snow shovel with....just in case...

Next 3 days down here will be interesting for weather.

cook_dw · #**268** 12-19-2022, 06:52 PM

I like this car a lot.

**napa68** · #**269** 12-22-2022, 06:02 PM

The L88 is apart and all has held up well. The block, cylinder bores, pistons (TRW 12.5:1), crank journals all look good as does the dimple rods (bushed for floating pins). The ZL1 cam and lifters all look good, measured out to spec, and will be reused.

The only issue that was discovered is the flywheel was way out of balance (for whatever reason). That will get addressed and balanced with the pressure plate. I did notice there was a vibration above 5000 rpm. While it wasn't terrible, I felt it should be better. Glad we found a smoking gun there.

So, a simple hone job and hot tank. All new rings, bearings, and gaskets. We'll add the 842 aluminum heads I had redone earlier this year (for this little side project) in addition to another 163 intake (divider milled out).

Eric Jackson helped me source an old school Holley 4781 850DP. He should have that tomorrow to build a trick little carb specifically for this combination. I suspect by the end of January it should be on the dyno.

Merry Christmas everyone!

**dykstra** · #**270** 12-22-2022, 09:02 PM

Great to hear Tim!!

The Following User Says Thank You to WILMASBOYL78 For This Useful Post:
napa68 (11-25-2022)

The Following User Says Thank You to TimG For This Useful Post:
napa68 (11-25-2022)

The Following 3 Users Say Thank You to napa68 For This Useful Post:
69M22Z (11-26-2022), dykstra (11-26-2022), olredalert (11-25-2022)

The Following 13 Users Say Thank You to napa68 For This Useful Post:
1967Z28 (12-12-2022), 427 (01-04-2023), 69M22Z (12-13-2022), big gear head (12-13-2022), cook_dw (12-16-2022), Crush (12-12-2022), dykstra (12-12-2022), John (12-20-2022), juliosz (12-12-2022), L78M22Rag (12-16-2022), olredalert (12-12-2022), PeteLeathersac (12-13-2022), Too Many Projects (12-12-2022)

The Following User Says Thank You to dykstra For This Useful Post:
napa68 (12-12-2022)

The Following User Says Thank You to cook_dw For This Useful Post:
napa68 (12-19-2022)

The Following 8 Users Say Thank You to napa68 For This Useful Post:
1967Z28 (12-22-2022), 69M22Z (12-22-2022), big gear head (12-22-2022), dykstra (12-22-2022), juliosz (12-22-2022), olredalert (12-22-2022), RPOLS3 (12-24-2022), Steve Shauger (12-22-2022)