|
|
|
#1
10-19-2021, 12:01 AM
|
||||
|
||||
Blackjack Headers
I acquired a set of NOS Blackjack headers. The part number is 3017. Unfortunately, I can’t find that number anywhere. Does anyone have an old catalog to match it up?
The story is, they were mocked up in a 1970 Chevelle but never used. Thanks in advance, Kurt
__________________
 1969 SS396 Post Sedan Delivered to Van-T Topeka KS MCACN Day2 Concourse Gold Award 1968 Schwinn Orange Krate 1969 Schwinn Pea Picker 1968 Schwinn 5-Speed 1970 Schwinn 3-Speed Deluxe 1972 Schwinn 10-Speed Continental 1973 Schwinn 5-Speed Suburban All Original Paint Bikes 
|
|
#2
10-19-2021, 03:11 AM
|
||||
|
||||
|
'
Comparing w/ other Blackjack/Appliance Headers, they appear more Camaro like than 'Velle?  1'st pic below is your pipes compared w/ Nos '68-72 Velle pipes from this thread, note swept back angle of mid runners... https://www.yenko.net/forum/showthread.php?p=1301952 2'nd pic is yours compared to 1'st Gen Pipes from this second linked thread, pass' side looks different for accessories perhaps but driver's almost the same other than pic angle?... https://www.yenko.net/forum/showthread.php?p=1260298 Also of note in the second linked thread is Member Whitetop mentions he has a Blackjack Catalogue. Best of luck!  ~ Pete .
__________________
I like real cars best...especially the REAL real ones!
|
| The Following 2 Users Say Thank You to PeteLeathersac For This Useful Post: | ||
69 Post Sedan (10-20-2021), olredalert (03-21-2024) | ||
|
#3
10-19-2021, 03:19 PM
|
||||
|
||||
|
I have a catalog. Remind me in case I don't post the information tonight.
|
|
#4
10-19-2021, 04:16 PM
|
||||
|
||||
|
Hi Kurt! Those look identical to my Appliance CH4s, which are for 67-69 Camaro. You can see mine on my build thread.
https://www.yenko.net/forum/showthread.php?t=161440 Last edited by Chuck_Burg; 10-19-2021 at 07:46 PM. Reason: Typo
|
| The Following User Says Thank You to Chuck_Burg For This Useful Post: | ||
69 Post Sedan (10-20-2021) | ||
|
#5
10-20-2021, 01:32 AM
|
|||
|
|||
|
Quote:
I put a lot of those Appliance headers on in the early 70,s when I worked at a local Calgary speedshop JB,s Automotive , very nice headers very equal length too. I have a set of CH3 headers for a small block Camaro been saving them for years. FWIW when Blackjack took over they changed to that rotating lower flange. Last edited by rszmjt; 10-20-2021 at 01:34 AM.
|
| The Following 2 Users Say Thank You to rszmjt For This Useful Post: | ||
69 Post Sedan (10-20-2021), NorCam (10-20-2021) | ||
|
#6
10-20-2021, 04:16 PM
|
||||
|
||||
|
Good note on the rotating collector flange, which is probably an improvement. The Appliance headers have four hole square collector flanges.
|
|
#7
10-20-2021, 06:34 PM
|
|||
|
|||
|
Quote:
I have Tig welded the flange both sides before and then ground and Roloxed off the flared bulge. I also noticed the quality of the bends and port flanges etc got worse when they changed to Blackjack name. JMO. I put many different make headers on the 67-69 Camaros and Appliance was the only 1 that did not have any clearance issues with steering box/pitman arm or frame fuel line. etc. Wish they still were available. Last edited by rszmjt; 10-20-2021 at 06:37 PM.
|
|
#8
10-20-2021, 08:10 PM
|
||||
|
||||
|
The Appliance fit in my 67 like a glove! I was very impressed when I installed mine.
|
|
#9
10-22-2021, 03:34 AM
|
||||
|
||||
|
Enjoy.
|
| The Following 3 Users Say Thank You to jbtech For This Useful Post: | ||
|
#10
10-22-2021, 05:33 PM
|
||||
|
||||
|
'
W  W also cool they're B-Body!Note the 'Vette pipes are the only other application shown w/ 2" runners and 3-1/2" collectors. As above, they're similar to F-Body so may swap/fit one or both applications? ~ Pete .
__________________
I like real cars best...especially the REAL real ones!
|
| The Following 2 Users Say Thank You to PeteLeathersac For This Useful Post: | ||
69 Post Sedan (10-22-2021), Chuck_Burg (10-22-2021) | ||
 |
|
|
Linear Mode
