|
Register | Album Gallery | Thread Gallery | FAQ | Members List | Calendar | Become a Paid Member | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
Saginaw smog pump rebuild
Anybody had a smog pump completely apart? I'm working with the drum inside & I was wondering if the end where the large bearing is, it looks like a spanner wrench would be used. Does that part actually unscrew? I wanted to clean it real good which would require removing the vains. Thank you, Joe
__________________
1968 Z/28 Corvette Bronze. Black Hounds Tooth. 02E Los Angeles born 3/13/1968 pnt OO 1969 SS396 Yellow/Yellow 08E Norwood born 8/28/1969 pnt 76E 1970 'cuda Moulin Rouge, 440-6, 4 speed |
#2
|
|||
|
|||
The fan is a press fit. If that is what you are talking about.
|
#3
|
||||
|
||||
I have a Pair Devaning in progress.
The Large Torrington Bearing is mounted in an ENDPALTE that is then pressed into the open end of the rotor barrel. I used a three-jaw puller with the legs rotated and pressed against a solid piece of round stock placed inside the rotor cavity, to Pull the endplate with Bearing. Another option is to press the bearing down inside the rotor barrel and pull it out, but often the rotor blades and internal bearings are a source of interference. I ONLY work on De Vaneing them, Not interested in a working pump. Llyods instructions over at Camaros.net were very very helpful
__________________
69 Los Z11 68 SS/RS 396/325 68 Los Z28 Last edited by 169indy; 08-09-2022 at 03:39 AM. |
#4
|
||||
|
||||
Yes, I'm trying to remove the end plate to get access to the rotors. I'm trying to make it a working unit. Sounds like the end plate is pressed in....Thank you, Joe
__________________
1968 Z/28 Corvette Bronze. Black Hounds Tooth. 02E Los Angeles born 3/13/1968 pnt OO 1969 SS396 Yellow/Yellow 08E Norwood born 8/28/1969 pnt 76E 1970 'cuda Moulin Rouge, 440-6, 4 speed |
#5
|
||||
|
||||
Removing Rotor Barrel Endplate
I used 2 leg puller with jaws reversed and pulled on the inner race, the bearing outer race fit held and the endplate pulled out from the barrel allowing access to the Vanes intact.
I have found OEM Vanes are Plastic and Rebuilt units have (GME) G9 Glass Melamine Epoxy Vanes. The Woven Glass vanes do not "Shatter" like the plastic one and are very difficult to remove necessitating endplate removal as if doing a usable rebuild. I think I used a smaller diameter support that would fit the Vanes intact for one pump and the other the plastic were destroyed.
__________________
69 Los Z11 68 SS/RS 396/325 68 Los Z28 |
The Following User Says Thank You to 169indy For This Useful Post: | ||
X66 714 (08-09-2022) |
#6
|
||||
|
||||
Thank you...Joe
__________________
1968 Z/28 Corvette Bronze. Black Hounds Tooth. 02E Los Angeles born 3/13/1968 pnt OO 1969 SS396 Yellow/Yellow 08E Norwood born 8/28/1969 pnt 76E 1970 'cuda Moulin Rouge, 440-6, 4 speed |
The Following User Says Thank You to X66 714 For This Useful Post: | ||
169indy (08-10-2022) |
#7
|
||||
|
||||
Quote:
https://www.camaros.net/threads/1969...337897/page-31 |
#8
|
||||
|
||||
Thank you....Joe
__________________
1968 Z/28 Corvette Bronze. Black Hounds Tooth. 02E Los Angeles born 3/13/1968 pnt OO 1969 SS396 Yellow/Yellow 08E Norwood born 8/28/1969 pnt 76E 1970 'cuda Moulin Rouge, 440-6, 4 speed |
#9
|
||||
|
||||
Quote:
|
The Following User Says Thank You to napa68 For This Useful Post: | ||
Edgemontvillage (12-11-2023) |
Thread Tools | |
Display Modes | |
|
|