|
Register | Album Gallery | Thread Gallery | FAQ | Community | Calendar | Become a Paid Member | Today's Posts | Search |
|
Thread Tools | Display Modes |
#212
|
||||
|
||||
The original owner simply cut two slits on the left side of the shifter hole and bent it down. I bent it back up so the original shifter boot will screw right into the factory location. I'll just seal where the two slits were made for now. The car has other areas of butchery that will be addressed down the road but the metalwork isn't a priority at this point. I simply want to resurrect the car while making the interior nice. I'm either going to run the early hurst shifter with the 4527 stick or a P&G shifter. Either way it's not going to be a factory shifter for now.
|
#213
|
||||
|
||||
Muncie refreshed with new gaskets, seals, and Thrust washers. I had to install a helicoil because one of the bearing retainer bolts was simply epoxied to the case.
Engine and transmission finally in the car. A lot of little things to be done before first fire up. Last edited by jbtech; 08-27-2023 at 04:02 AM. |
The Following 15 Users Say Thank You to jbtech For This Useful Post: | ||
169indy (08-27-2023), 1967Z28 (08-27-2023), 69M22Z (08-27-2023), Andy (08-29-2023), big gear head (08-27-2023), carnut4life (08-27-2023), Dave Rifkin (08-27-2023), dykstra (08-27-2023), L_e_e (08-28-2023), napa68 (08-27-2023), Oldss (09-17-2023), olredalert (08-27-2023), RPOLS3 (08-28-2023), Steve Shauger (08-28-2023), Too Many Projects (08-27-2023) |
#214
|
||||
|
||||
Yay!
|
#215
|
||||
|
||||
Woke up to make sure it was real.
Last edited by jbtech; 08-27-2023 at 03:57 PM. |
The Following 7 Users Say Thank You to jbtech For This Useful Post: | ||
big gear head (08-28-2023), dykstra (08-29-2023), Oldss (09-17-2023), olredalert (08-28-2023), PeteLeathersac (09-17-2023), scuncio (08-27-2023), Steve Shauger (08-28-2023) |
#218
|
||||
|
||||
This engine was originally built for my 67 Base model Day2 big block swap project so it is by no means a pure 67 engine.
It is a 70's 2 bolt (studs) main block, 077 heads, 198 intake, 3521 crank, list goes on. With all that in mind I wanted this engine to look like a NOM built up with all of the 67 touches swapped over. Some of the 67 only goodies include but not limited to: March 67 3910 Alt+Pulley Valve Covers Crank/Water Pump Pulley PCV Brackets (square tab pcv hose clamps installed after pics taken) I used thick valve cover gaskets and studs to clear the polylocks. The RH temp sender on the intake is for a sun greenline gauge The M/T Super Scavenger headers fit absolutely perfectly I installed the shifter into final position after mocking up the seat, steering wheel, and console. (the shifter is in gear in the photo because my 4 year old son was "driving to grandma's house" Last edited by jbtech; 09-17-2023 at 07:57 PM. |
The Following 5 Users Say Thank You to jbtech For This Useful Post: | ||
1967Z28 (09-17-2023), 69M22Z (09-17-2023), big gear head (09-18-2023), dykstra (09-17-2023), jer (09-26-2023) |
#219
|
||||
|
||||
Mocked up Bruce's custom made plenum air cleaner. He modified a Chevelle air cleaner he removed from the salvage yard back in 1967. He was inspired by the other Camaros at the drag strip and decided to make his own. He says he used a 16" inner tube to seal the air cleaner duct to firewall.
Whatever he used to seal it left a pattern on the firewall (last pic) Last edited by jbtech; 09-17-2023 at 09:17 PM. |
The Following 6 Users Say Thank You to jbtech For This Useful Post: | ||
169indy (09-17-2023), big gear head (09-18-2023), dykstra (09-17-2023), olredalert (09-18-2023), PeteLeathersac (09-17-2023), R68GTO (09-17-2023) |
#220
|
||||
|
||||
67 clutch and fan installed. Fan retains"day2" chrome.
|
The Following 5 Users Say Thank You to jbtech For This Useful Post: | ||
1967Z28 (09-18-2023), big gear head (09-18-2023), dykstra (09-20-2023), L_e_e (09-18-2023), PeteLeathersac (09-18-2023) |
Tags |
1967, 396 ss, l78 camaro |
|
|