![]() |
|
Register | Album Gallery | Thread Gallery | FAQ | Community | Calendar | Become a Paid Member | Today's Posts | Search |
![]() |
|
Thread Tools | Display Modes |
#161
|
|||
|
|||
![]()
I have dehumidifiers on storage and paint booth. Thought about a mini split for the paint booth but just another thing that is a want rather than a need. I was chuckling a bit about the working in the shop. They took the Methylene out of the stripers because it was causing people to pass out! Even with it now gone i do it all open air. I love this hobby but id like to be around and kicking for years to come
![]() |
#162
|
|||
|
|||
![]()
Some cars seem to have some surface rust which is always alot of work to get clean. I strip the paint and then get out muriatic acid. Nasty stuff to work with. Doesnt take too long for the rust pits to disappear. This roof was not too bad but still a multi day event to get cleaned and neutralized before starting the first step of body work.
|
The Following 5 Users Say Thank You to OneStopRestoration For This Useful Post: | ||
69M22Z (08-31-2024), Dave Rifkin (09-01-2024), dykstra (09-01-2024), gtomike1967 (08-31-2024), Tenney (09-01-2024) |
#163
|
|||
|
|||
![]()
Question, after the muriatic acid and neutralizing, do you put anything on the metal to prevent flash rust? TIA
|
#164
|
||||
|
||||
![]()
I’m also curious how you apply and neutralize the muriatic acid.
|
#165
|
|||
|
|||
![]()
No, its just alot of hard work after that. Wire wheel the entire top, followed by a d/a. Even after doing a day of body fill and blocking I will probably hit it again before putting down some primer. I think a little OCD at this stage will pay dividends later.
|
#166
|
|||
|
|||
![]()
You just need a strong base solution like water and baking soda. You will still get some amount of light rust, just no way to get around it.
|
The Following 2 Users Say Thank You to OneStopRestoration For This Useful Post: | ||
olredalert (09-01-2024), scuncio (09-02-2024) |
#167
|
||||
|
||||
![]()
Thanks for posting your work although i know this stuff takes time I look daily for updates!
__________________
1969 SS 396 300 deluxe post car 1969 SS 396 300 deluxe hardtop 1969 SS 396 chevelle 1978 chevy shortbed step side 1983 chevy shortbed 1985 chevy shortbed If a hammer and duct tape wont fix it u have electrical problems! Last edited by chevyman0429; 09-02-2024 at 01:54 PM. |
The Following 4 Users Say Thank You to chevyman0429 For This Useful Post: | ||
66BoxNova (09-01-2024), Bill Pritchard (09-01-2024), OneStopRestoration (09-02-2024), ragtop (09-01-2024) |
#168
|
|||
|
|||
![]()
After stripping its hammer out the dents, followed by the base layer of filler. I wanna point out that the better job of hammering out the dents the less filler you have which is the primary goal. I realize this roof looks bad but there is very sliver thin areas of filler here. After that epoxy prime followed by standard primer.
This paves the way to about a dozen additional rounds of blocking and sanding. |
The Following 15 Users Say Thank You to OneStopRestoration For This Useful Post: | ||
66BoxNova (09-02-2024), 69M22Z (09-02-2024), big gear head (09-02-2024), Bill Pritchard (09-02-2024), chevyman0429 (09-02-2024), Dave Rifkin (09-02-2024), dykstra (09-02-2024), gtomike1967 (09-02-2024), Hawkeye (Yesterday), Jonesy (Yesterday), McCune (Yesterday), olredalert (09-02-2024), ragtop (09-02-2024), RPOLS3 (09-02-2024), Tuna Joe (09-02-2024) |
#169
|
|||
|
|||
![]()
Aside from body work finishing up chassis items one at a time. I dont have the time, patience or money to try and get a driveshaft back to bare metal and have it look good, so painted works just fine for me.
|
The Following 8 Users Say Thank You to OneStopRestoration For This Useful Post: | ||
Bill Pritchard (Yesterday), chevyman0429 (Yesterday), Dave Rifkin (Yesterday), dykstra (Yesterday), olredalert (Yesterday), RPOLS3 (Yesterday), Tenney (Yesterday), Tuna Joe (Yesterday) |
![]() |
|
|