|
Register | Album Gallery | Thread Gallery | FAQ | Community | Calendar | Become a Paid Member | Today's Posts | Search |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
GM A body fuel line replacement?
Hi,
I recently bought a 1967 GTO convertible. In my haste to start working on it I ordered a new fuel tank and a new fuel line from the tank to the fuel pump. I have now realized that its probably impossible to replace the fuel line while the body is on the frame? Inline Tube says its possible but very difficult. So im wondering what options I have for a new fuel line? I see kits with steel lines and some bending and flaring tools but I have a feeling steel lines might be a little hard for an amateur like me? I have seen some kits with aluminum lines that are supposed to be easier but will require a different type of fitting. What have you all done in the past? Removing the body or even lifting it is not an option. Thank you |
#2
|
||||
|
||||
The hard part is the rear, there is a clamp up on top of the spring pocket
I’ve heard of guys jacking up the body at the rear to get over the spring pocket. It may be possible to get the rear over and bow the middle of the line and then poke the front thru while taking the bow out. Install the rubber fuel pump line and clamp first, leave that rubber line long and trim later.
__________________
Steve 67 Chevelle SS |
#3
|
||||
|
||||
Quote:
When I faced this it lead to a full chassis restoration. (Not a bad option) |
#4
|
||||
|
||||
This is how I lifted the body on my Chevelle to install a 1 piece trunk floor, that I had been told wasn't possible with the body on the frame... I used 2 floor jacks with 12" long 2x2 boards under the rocker panels and removed all the body bolts but the front 2, yours will have 4 and I would only leave the 2 inside in but loosen them a couple turns. I had the body about 8" above the rear crossmember. In the second pic, you can see the fuel line on the right side, yours will be on the left, but same configuration.
Your new fuel line with come bent in half for shipping so you may be able to open it only enough to snake the rear, over the frame, section in place and then work the front in as you straighten the rest, like 67SS4speed suggested. The rear section does take a hard turn back toward the center of the car and you may need to straighten that some to get it over the frame and then re-shape it to point toward the sender. If the body mounts are deteriorated, this is a good time to replace them too. We have a lot of folks in the Chi-town area who may be willing to help with this, if you are in that area. Unfortunately, I am 8 hours away, or I would bring my jacks and help.
__________________
Mitch 1970 Chevelle SS 1966 Chevelle SS 1967 Camaro ss/rs 1938 Business coupe, street rod 2000 FXSTS, original owner, 13k miles |
#5
|
|||
|
|||
When I did the body off restoration on my 66 GTO, the original fuel line running the length of the frame looked mint- so I decided to keep it.
After all was said & done, and the car was back together- getting ready to start the engine- no fuel. I first tried blowing through the line with air. Then tried running a wire through. Then spinning the wire on a drill. No dice- blocked. Damn. No way. I'm not pulling the car back apart. Bought the one-piece original line from Ames, and replaced it. If you have the car up high on a lift, it's not a bad job at all. Quick & easy. As mentioned, the line comes bent in half to start- you just unbend and start sneaking it in front & rear. You do have to bend the line slightly, and then bend it back after sneaking it in front and rear- but it wasn't too tough. And you can't tell it was ever bent if you're careful. Last edited by 3X24SPD; Today at 09:07 AM. |
|
|