![]() |
#21
|
|||
|
|||
![]()
Not trying to jinx you here, but I think I would have run 100% hard line for this. That rubber coupler just looks like a leak waiting to happen. Probably won't ever be an issue. Just always looking for places for Murphy to show up. I hate that guy.
__________________
Don't believe everything you read on the internet ... Ben Franklin |
#22
|
|||
|
|||
![]() Quote:
I already replaced it...... That was the last scrap piece I had laying around....All fixed now Ken
__________________
![]() The Best things in life......Aren't Things |
#23
|
|||
|
|||
![]()
Almost didn't say anything. Don't want to sound like a wise a$$.
Really enjoying this build, as I enjoy all of your builds.
__________________
Don't believe everything you read on the internet ... Ben Franklin |
The Following User Says Thank You to Lynn For This Useful Post: | ||
kwhizz (05-07-2023) |
#24
|
|||
|
|||
![]()
Had a problem with the Image hosting site......Think I got it figured out finally......So....I received the new radiator and put it in to see what the next set of problems that are going to pop up were......LOL.... Very limited room for anything.. The Throttle body with elbow is 1/2" away from the Radiator.....The Electric fan has about 1" of clearance.....I have to see about moving the A/C condenser behind the core support and getting the Heat exchanger to fit in front of the core support is going to be an issue........But...In the meantime I finished the air inlet tube ........More pic's to come
![]() ![]() ![]()
__________________
![]() The Best things in life......Aren't Things |
The Following 8 Users Say Thank You to kwhizz For This Useful Post: | ||
Arrowsmith (05-17-2023), Big Block Bill (05-17-2023), dykstra (05-18-2023), napa68 (05-17-2023), olredalert (05-17-2023), RPOLS3 (05-19-2023), Tenney (05-17-2023), Xplantdad (05-17-2023) |
#25
|
|||
|
|||
![]()
Getting to the part I have dreaded for a while....... Now that all the physical parameters are known.......Time to pull the engine out and install the wiring harnesses and see what other issues are going to pop up.......
![]() ![]() ![]() This is where patience is going to enter the picture.....Look at the size of the main harness ........ Hope there is room left in that 1 lb. bag to get this 10 lbs in there...
__________________
![]() The Best things in life......Aren't Things |
The Following 8 Users Say Thank You to kwhizz For This Useful Post: | ||
69M22Z (05-22-2023), Arrowsmith (05-22-2023), dykstra (05-22-2023), napa68 (05-22-2023), olredalert (05-22-2023), PeteLeathersac (05-22-2023), RPOLS3 (05-22-2023), Xplantdad (05-22-2023) |
#26
|
||||
|
||||
![]()
Wow!!!
![]()
__________________
Bruce Choose Life-Donate! |
The Following 2 Users Say Thank You to Xplantdad For This Useful Post: | ||
69M22Z (05-22-2023), Arrowsmith (05-22-2023) |
#27
|
|||
|
|||
![]()
----Sure hope no critters ever get a full tummy on any part of that harness!.....Bill S
|
#28
|
|||
|
|||
![]() |
#29
|
|||
|
|||
![]()
What ever happened to this project - I for one was very interested in seeing the outcome of all of the 'stuffing' since Chevy II's don't have a lot of space to say the very least..
|
#30
|
|||
|
|||
![]()
Nice work!
The LT platform is more complex in even the simplest ways. I loved the former rubber seal LS gaskets which never leaked when installed properly. The RTV deal works fine but is a pain in the @$$ to clean off, even more so with an egine in the car. We just finished up an LT4 1969 Camaro with a TKX 5 speed and will be starting an a 72 Nova with a built for boost L8T 402ci. What are those stock headers/manifolds off of? Looks like a great fit! |
![]() |
Thread Tools | |
Display Modes | |
|
|