15X7 steelies
 

Did GM ever make these??..if so what application??...are they reproduced??..Thanks

ALbert

Re: 15X7 steelies
 

I believe early 70's Chevy wagons had them...anyway, I have 4 of them in the barn along with some 15 x 6's.....I can check codes if it helps.

wilma

Re: 15X7 steelies
 

[ QUOTE ]
I believe early 70's Chevy wagons had them...anyway, I have 4 of them in the barn along with some 15 x 6's.....I can check codes if it helps.

wilma

[/ QUOTE ]

dont need any specific code..just a pair that match my front XT,s and I can mount some drag radials on!! https://www.yenko.net/ubbthreads/imag...ns/naughty.gif

Ill post in the classifieds..thanks

ALbert

Re: 15X7 steelies
 

-----Early 70s wagons would be 5-on-5 bolt pattern if I recall so make sure and measure before you buy........Bill S

Re: 15X7 steelies
 

Al
Will these work. https://www.yenko.net/ubbthreads/imag...lins/dunno.gif New Wheel Vintiques @ Summit Racing

http://store.summitracing.com/partdetail...mp;autoview=sku

A better photo.

http://wheelvintiques.com/shopsite_s...ml/page53.html

I think these have the correct bolt pattern and backspace as stock.

Mike

Re: 15X7 steelies
 

If you're at the boneyard, look at rims on rear swaybar equipped 77-90 Caprices..
Same small bolt pattern and supposedly these F41 cars were shipped w/ the 7" inside width rims...no idea if the same years if F41 equipped BOP variants have them too?.

https://www.yenko.net/ubbthreads/imag...lins/beers.gif
~ Pete

Re: 15X7 steelies
 

I have a old pair of them, dont recall where I found them but have had them for 20 yrs, last we had them on a 70 Chevelle and they fit nice, let me see if there not under a ton of stuff and see if they have any codes on them.

Re: 15X7 steelies
 

astro van.

Re: 15X7 steelies
 

[ QUOTE ]
Al
Will these work. https://www.yenko.net/ubbthreads/imag...lins/dunno.gif New Wheel Vintiques @ Summit Racing

http://store.summitracing.com/partdetail...mp;autoview=sku

A better photo.

http://wheelvintiques.com/shopsite_s...ml/page53.html

I think these have the correct bolt pattern and backspace as stock.

Mike

[/ QUOTE ]


Mike........Been down that Road with https://www.yenko.net/ubbthreads/images/graemlins/bs.gifWheel Vintiques https://www.yenko.net/ubbthreads/images/graemlins/bs.gif......Unless their Quality has Improved https://www.yenko.net/ubbthreads/images/graemlins/bs.gif.....Well......Enough Said.........

Ken https://www.yenko.net/ubbthreads/imag...mlins/flag.gif

Re: 15X7 steelies
 

Ken
I have only used one set of there wheels, and that is the 14x7 steelies that are on my black Camaro.
I have been driving on them all summer with no problem https://www.yenko.net/ubbthreads/imag...lins/dunno.gif
This set is made in the great state of Cali. I thought they were nice.
The one down side is they are not sized for a snug fit were they mate to the front hub or rear axle, in other words the center hole is larger that an OE wheel.
What was it you had problems with ? Just curious.
By the way, I am getting excited about Vette Fest. https://www.yenko.net/ubbthreads/imag...lins/laugh.gif

Mike https://www.yenko.net/ubbthreads/imag...lins/beers.gif