wanted 69 L78 block
 

need a KF block for a third week of Feb. 69 built car.

Re: wanted 69 L78 block
 

or I can use a CE block for the same date.

Re: wanted 69 L78 block
 

[ QUOTE ]
or I can use a CE block for the same date.

[/ QUOTE ]

Donnie, did you see this one for sale?

http://cgi.ebay.com/ebaymotors/ws/eBayIS...e=STRK:MEWAX:IT

Re: wanted 69 L78 block
 

Thanks Kurt.
I was a little late on this one.

Re: wanted 69 L78 block
 

[ QUOTE ]
Thanks Kurt.
I was a little late on this one.

[/ QUOTE ]

Sorry for the late notice...I will try to do better next time. https://www.yenko.net/ubbthreads/imag...mlins/wink.gif

Re: wanted 69 L78 block
 

I have this one on Ebay with an $1100 reserve. It is a it late but is a CE block.


Jason

http://cgi.ebay.com/ebaymotors/ws/eB...m=260538101195

Re: wanted 69 L78 block
 

I don't think the date is too late....it is my understanding the driveline warranty was 5 year/50,000 mile warranty on the major driveline components. This is why we see so many CE blocks in these 69 and 70 BB cars. In order to get the warranty (CE) block, something had to happen to the original motor. It might not have happened until a year or two later....so, a valid CE dated block would most likely be much later than the original build date of the vehicle. We have a CE block in our 70 Fathom Blue L78...it is dated 1972...I confirmed with the original owner the warranty replacement of the engine, following some over zealous driving. It is possible to have a CE block with a date well past the original build date. The only thing I'm not sure of is if the later 854 blocks were used only for the 402 engines...or did Chevy keep some 272's for the 396 application. My guess would be that either was acceptable for the situation...

wilma

Re: wanted 69 L78 block
 

I have a 1974 CE block in my car. Dan Vasic along with a lot of other people have discussed this. We cannot confirm it but the motor in my car "could" have been a replacement.

The car only has 40k miles on it and it was built the 3rd week in June of 1969 which would take it to at least June of 1974 so it could still have been in the warranty window.

So I would think Jason's block would be perfect for Donnie's car. https://www.yenko.net/ubbthreads/imag...lins/beers.gif

Re: wanted 69 L78 block
 

If a lot of those older guys, like Cumby, had kept their "foot out of it"...we wouldn't have so many CE motors https://www.yenko.net/ubbthreads/imag...mlins/grin.gif

wilma...NuYawk rep for Mr. Tibor https://www.yenko.net/ubbthreads/imag...mlins/flag.gif

Re: wanted 69 L78 block
 

Thanks for the info.

Re: wanted 69 L78 block
 

I have an 824 with date code D-24-71
I didn't look at the stamp codes tonight. It is a Std 4.125 bore w/factory 4 bolt. I guess that is a little to later a date code for your project unless it is a replacement code.

Adger Smith
Adger Smith Performance Engines
2802 W 7TH ST
Texarkana TX
903-794-7223 shop
903-824-4924 cell
[email protected] E-mail
www.adgersperf.com web site(no mail)

Re: wanted 69 L78 block
 

I have a JD 272 4 bolt block T0109JD vin looks to be 19W386381.
that ill trade for a CE 4 bolt block dated june,july or augest 69

Re: wanted 69 L78 block
 

[ QUOTE ]
I have a JD 272 4 bolt block T0109JD vin looks to be 19W386381.
that ill trade for a CE 4 bolt block dated june,july or augest 69

[/ QUOTE ]

Donnie, check that VIN stamp and engine code again...

JD is for a 69 Chevelle L78 4 speed...but the W in the VIN would indicate Nova application...the Novas were all JH motors...unless I'm missing something https://www.yenko.net/ubbthreads/imag...mlins/hmmm.gif

Re: wanted 69 L78 block
 

the vin is down by the oil filter in the rough cast and its real hard to read.

Re: wanted 69 L78 block
 

Donnie, I think that answers the question...it is probably a Chevelle VIN then. I have never seen a Nova BB VIN in that location...perhaps it has an A or K instead of a W.

thanks, wilma

Re: wanted 69 L78 block
 

upon further review it looks like a K

Re: wanted 69 L78 block
 

[ QUOTE ]
If a lot of those older guys, like Cumby, had kept their "foot out of it"...we wouldn't have so many CE motors https://www.yenko.net/ubbthreads/imag...mlins/grin.gif

wilma...NuYawk rep for Mr. Tibor https://www.yenko.net/ubbthreads/imag...mlins/flag.gif

[/ QUOTE ]

From the way I have seen some of you younger boyz drive your cars....I think you are correct... https://www.yenko.net/ubbthreads/imag...mlins/grin.gif

Re: wanted 69 L78 block
 

From the way I have seen some of you younger boyz drive your cars....I think you are correct... https://www.yenko.net/ubbthreads/imag...mlins/grin.gif

[/ QUOTE ]

I guess you'll just have to show us youngins' how it's dun https://www.yenko.net/ubbthreads/imag...mlins/grin.gif

Re: wanted 69 L78 block
 

Tom, Mike has already done that! Where were you???? https://www.yenko.net/ubbthreads/imag...ns/naughty.gif

Grady https://www.yenko.net/ubbthreads/imag...ins/3gears.gif

Re: wanted 69 L78 block
 

Tom, SCR#13, bring something.... https://www.yenko.net/ubbthreads/imag...iggthumpup.gif it's all fun. And if you don't want the passes I bet Dave McGaffe would help you out. https://www.yenko.net/ubbthreads/imag...mlins/grin.gif