Forum: Garages/shops..
09-08-2024, 04:35 AM
|
Replies: 28
Views: 12,404
The coated floor was a new pour that had cured...
The coated floor was a new pour that had cured for a few months.They initially did a urethane coating that failed almost right away because the chemical company sent them the wrong chemicals. The...
|
Forum: L78/L89 specific Forum
09-08-2024, 04:07 AM
|
Replies: 399
Views: 232,524
|
Forum: Garages/shops..
09-08-2024, 02:12 AM
|
Replies: 28
Views: 12,404
|
Forum: Supercar/Musclecar Discussion
09-06-2024, 09:06 PM
|
Replies: 114
Views: 60,081
That's exactly what I did. I incorrectly called...
That's exactly what I did. I incorrectly called the lower bearing housing "plastic end piece". I pressed the old bearing out of the lower bearing housing, using a brake cylinder hone I opened it up...
|
Forum: Supercar/Musclecar Discussion
09-05-2024, 11:11 PM
|
Replies: 114
Views: 60,081
Here is What I used: ...
Here is What I used:
https://www.ss396.com/camaro/FBK-678.html
The Bearing is encapsulated into the Lower Bearing Housing, I never thought about extracting the Bearing ONLY and re encapsulating...
|
Forum: Supercar/Musclecar Discussion
09-04-2024, 01:42 PM
|
Replies: 3
Views: 1,313
|
Forum: Supercars/Musclecars-For Sale
09-02-2024, 08:58 PM
|
Replies: 11
Views: 1,400
1965 Impala SS 396/425 Project
I'll offer this up here before going to a wider audience. I'd love to see it go to one of the good people on this site.
This is a 1965 Impala Super Sport that originally came with a 396 / 425. ...
|
Forum: Member's Rides
09-02-2024, 01:31 PM
|
Replies: 169
Views: 93,974
Rough in Complete
After stripping its hammer out the dents, followed by the base layer of filler. I wanna point out that the better job of hammering out the dents the less filler you have which is the primary goal. ...
|
Forum: Supercar/Musclecar Discussion
08-31-2024, 01:51 PM
|
Replies: 18
Views: 1,697
|
Forum: AMC
08-29-2024, 10:36 AM
|
Replies: 14
Views: 1,891
Morning update on the gasser.
Front cover is...
Morning update on the gasser.
Front cover is assembled and clearances are set. Gears stick out of the case .006-.007” selected a gasket that I measured at .009. Meaning loose I’ll have clearances...
|
Forum: Comments, Suggestions, Problems
08-29-2024, 01:31 AM
|
Replies: 10
Views: 531
Test
1968 catalog
267528
1969 catalog
267529
|
Forum: Comments, Suggestions, Problems
08-29-2024, 01:20 AM
|
Replies: 10
Views: 531
|
Forum: AMC
08-27-2024, 07:12 PM
|
Replies: 44
Views: 22,433
Small update on the Hornet.
I’ve driven the...
Small update on the Hornet.
I’ve driven the car a bunch. It let me down one time when the factory tach shit the bed and I had to bypass it on the side of the road. I’ve since bypassed it correctly...
|
Forum: Supercars/Musclecars-For Sale
08-27-2024, 12:15 AM
|
Replies: 24
Views: 3,566
|
Forum: Ebay & other seen ads section
08-26-2024, 07:36 PM
|
Replies: 6
Views: 970
|
Forum: Supercars/Musclecars-For Sale
08-25-2024, 08:21 PM
|
Replies: 24
Views: 3,566
This car also took 1st place at the Boca Raton...
This car also took 1st place at the Boca Raton Concours car show. It was aslo voted by the AACA Judges as Muscle Car of the Year which is no small feat given that it was Judged against the thousands...
|
Forum: Preservation forum
08-25-2024, 03:39 AM
|
Replies: 105
Views: 49,653
|
Forum: Chevrolet
08-23-2024, 02:55 PM
|
Replies: 24
Views: 1,431
|
Forum: Chevrolet
08-23-2024, 01:34 PM
|
Replies: 24
Views: 1,431
|
Forum: Chevrolet
08-23-2024, 12:20 PM
|
Replies: 24
Views: 1,431
Garwood Motorboat Corvette
Garfield Wood was a successful businessman born in 1880 and had a passion for wooden racing boats. He built and raced many world record boats in the 20’s including numerous Miss America named boats....
|
Forum: L78/L89 specific Forum
08-22-2024, 05:08 AM
|
Replies: 399
Views: 232,524
I swapped my M22 for an Autogear transmission...
I swapped my M22 for an Autogear transmission that fit my needs as a driver with 3.31 ring and pinion and wide torque band. I ordered mine with the following ratios
1st 2.994
2nd 1.879
3rd 1.353...
|
Forum: Lounge
08-21-2024, 08:16 AM
|
Replies: 992
Views: 444,165
|
Forum: Technical & Restoration
08-20-2024, 01:09 PM
|
Replies: 21
Views: 2,648
I have more often than not had leaks in my 12...
I have more often than not had leaks in my 12 bolt cover, with or without gasket, with or without black RTV. That is until I started using Permatex's 81182 Gear Oil gasket maker. I still use the...
|
Forum: Supercar/Musclecar Discussion
08-19-2024, 03:50 PM
|
Replies: 31
Views: 4,484
|
Forum: Pit Area - Racing
08-18-2024, 08:40 PM
|
Replies: 604
Views: 364,413
|