Forum: Supercars/Musclecars-Sold listings
11-11-2024, 04:54 PM
|
Replies: 19
Views: 2,772
|
Forum: Supercars/Musclecars-Sold listings
11-05-2024, 04:34 AM
|
Replies: 19
Views: 2,772
|
Forum: Chevrolet
10-30-2024, 03:06 PM
|
Replies: 29
Views: 1,867
|
Forum: Supercar/Musclecar Discussion
10-24-2024, 12:31 PM
|
Replies: 51
Views: 31,550
Here's some more pictures. I have the correct...
Here's some more pictures. I have the correct fender mounted turn signal lights. Other than that, I think the exterior is done. I still have the rear speaker to install, repair the RH seat track &...
|
Forum: Supercar/Musclecar Discussion
10-23-2024, 09:45 PM
|
Replies: 51
Views: 31,550
|
Forum: Member's Rides
10-20-2024, 10:29 PM
|
Replies: 201
Views: 114,655
Body Sand Blasting
Unlike the frame the body is quite the olympic event in sand blasting. Made a pretty good dent this weekend considering I did a door and part of the deck lid edges Saturday. I also spent some time...
|
Forum: Lounge
10-03-2024, 02:35 AM
|
Replies: 1,037
Views: 508,513
|
Forum: Member's Rides
09-09-2024, 02:04 AM
|
Replies: 201
Views: 114,655
Thanks to some mice
This is one that is a first for me. Upon doing some window channel sand blasting i found the package tray area undeer the dutchman panel was pinholes from rust. After investigating and blowing out...
|
Forum: Parts/Memorabilia - For Sale
09-06-2024, 09:35 PM
|
Replies: 2
Views: 343
|
Forum: Technical & Restoration
09-06-2024, 03:19 PM
|
Replies: 19
Views: 2,942
I always check the timing mark on a engine that...
I always check the timing mark on a engine that I'm building using a piston stop before putting the heads on. I never trust it until I verify that it's correct. I even verify TDC on a running engine...
|
Forum: Member's Rides
09-02-2024, 02:31 PM
|
Replies: 201
Views: 114,655
Rough in Complete
After stripping its hammer out the dents, followed by the base layer of filler. I wanna point out that the better job of hammering out the dents the less filler you have which is the primary goal. ...
|
Forum: Lounge
08-14-2024, 02:44 AM
|
Replies: 34
Views: 4,800
|
Forum: Lounge
08-09-2024, 01:54 AM
|
Replies: 34
Views: 4,800
|
Forum: Lounge
08-08-2024, 11:32 PM
|
Replies: 34
Views: 4,800
|
Forum: Lounge
08-06-2024, 12:11 PM
|
Replies: 34
Views: 4,800
|
Forum: Nickey Chevrolet & Bill Thomas Performance
07-03-2024, 01:24 PM
|
Replies: 4
Views: 4,508
Big Thanks to Stefano!!
My daughter and I were at “Sick Week” drag and drive event at Byron Dragstrip several weeks ago and ran into Stefano.
He hooked her up with some Nickey swag.
Thanks again Stefano!:youguysrock:
...
|
Forum: Member's Rides
06-23-2024, 04:17 PM
|
Replies: 201
Views: 114,655
Color Spray Out and bunch of misc items
Weekend of running. zinc and yellow zinc plating done. Radiator being recored. Picked up some sample 72 paint for a color spray out test. Looks very close,
|
Forum: Chevrolet
06-20-2024, 11:21 PM
|
Replies: 12
Views: 5,070
|
Forum: Parts/Memorabilia - For Sale
06-20-2024, 02:57 PM
|
Replies: 2
Views: 836
|
Forum: Ebay & other seen ads section
06-19-2024, 04:34 AM
|
Replies: 7
Views: 3,568
|
Forum: In Memoriam
05-31-2024, 04:52 AM
|
Replies: 21
Views: 7,661
Cliff Ernst
https://www.hendersonvillefh.com/obituaries/clifford-ernst
|
Forum: Ebay & other seen ads section
05-28-2024, 08:23 PM
|
Replies: 7
Views: 2,818
No strike at Norwood.
Fisher Body skipped...
No strike at Norwood.
Fisher Body skipped 02C; 02D builds span 18 production days and almost 13,000 units.
Van Nuys was on strike April 28-June 18. The last 1,000 or so units were a mix of 04D...
|
Forum: Auctions
05-25-2024, 04:53 PM
|
Replies: 12
Views: 4,463
|
Forum: Lounge
05-22-2024, 09:41 PM
|
Replies: 23
Views: 11,605
I HAD all air stuff over the years, lines and...
I HAD all air stuff over the years, lines and outlets all over the garage, but now I have 18v Milwaukee impacts/sockets and these things are animals. I can just leave them on the workbench for weeks...
|
Forum: Auctions
05-22-2024, 01:31 AM
|
Replies: 40
Views: 17,631
|