Forum: Supercar/Musclecar Discussion
07-18-2024, 04:42 PM
|
Replies: 11
Views: 1,313
|
Forum: Sponsors Forum
05-16-2024, 11:43 PM
|
Replies: 13
Views: 8,674
|
Forum: Technical & Restoration
05-07-2024, 07:15 PM
|
Replies: 11
Views: 3,821
|
Forum: Technical & Restoration
04-03-2024, 02:00 PM
|
Replies: 3
Views: 1,722
Window Regulator Rollers
I have searched every possible vendor for the front door window regulator rollers. It seems like they all offer the same design roller. My picture shows how different the original roller is compared...
|
Forum: Technical & Restoration
02-29-2024, 08:29 PM
|
Replies: 14
Views: 2,696
|
Forum: Technical & Restoration
02-21-2024, 03:15 PM
|
Replies: 6
Views: 1,260
I made a tubular rivet tool out of an old punch...
I made a tubular rivet tool out of an old punch on a lathe too. I also made a fitting to go in this rivet tool to get to areas where a punch was too big and you couldn't use a hammer to peen over the...
|
Forum: Technical & Restoration
09-24-2023, 10:53 PM
|
Replies: 1
Views: 956
|
Forum: Technical & Restoration
07-28-2023, 01:12 AM
|
Replies: 8
Views: 1,890
|
Forum: Parts/Memorabilia - Wanted
07-01-2023, 10:51 PM
|
Replies: 2
Views: 1,196
|
Forum: Parts/Memorabilia - Wanted
02-05-2023, 12:46 PM
|
Replies: 2
Views: 1,009
|
Forum: Technical & Restoration
01-29-2023, 01:08 PM
|
Replies: 8
Views: 2,044
|
Forum: Parts/Memorabilia - Sold listings
01-15-2023, 02:15 AM
|
Replies: 3
Views: 1,227
|
Forum: Supercar/Musclecar Discussion
01-13-2023, 03:02 PM
|
Replies: 7
Views: 2,104
|
Forum: Sponsors Forum
12-30-2022, 05:35 PM
|
Replies: 52
Views: 26,351
I had the opportunity to pick-up my exhaust...
I had the opportunity to pick-up my exhaust system yesterday at Gardner Exhaust. It was a pleasure to meet Eric and tour his facility. He is definitely an asset to the car hobby and is a car...
|
Forum: Parts/Memorabilia - For Sale
12-15-2022, 06:31 PM
|
Replies: 1
Views: 1,458
Mopar Performance Shirt
I got this shirt when I was doing the towing at the Mopar Nationals in Englishtown New Jersey. The shirt was so nice I didn't wear it that week and never worn it since. The shirt is made in the USA...
|
Forum: Baldwin-Motion Performance
10-13-2022, 01:12 PM
|
Replies: 10
Views: 4,332
1968 Corvette
Besides the NCRS shipping report how do I tell if a 1968 Corvette was a Baldwin Motion Corvette? I know about the headlights, what other signs do I look for to validate the Corvette is a Baldwin...
|
Forum: Parts/Memorabilia - Wanted
08-03-2022, 01:58 PM
|
Replies: 8
Views: 3,257
|
Forum: Technical & Restoration
03-07-2022, 02:32 AM
|
Replies: 2
Views: 1,432
|
Forum: Technical & Restoration
10-14-2021, 11:42 PM
|
Replies: 5
Views: 2,043
I also cut a slot in a piece of wood big enough...
I also cut a slot in a piece of wood big enough for the wire harness to slide through so the socket sits on top of the wood. Then I used two pieces of metal strips and "C" clamps to hold the housing...
|
Forum: Parts/Memorabilia - Wanted
09-10-2021, 08:24 PM
|
Replies: 8
Views: 3,779
|
Forum: Technical & Restoration
07-23-2021, 01:13 PM
|
Replies: 7
Views: 3,407
|
Forum: Technical & Restoration
07-12-2021, 08:20 PM
|
Replies: 17
Views: 5,870
|
Forum: Parts/Memorabilia - Wanted
04-08-2021, 01:31 AM
|
Replies: 2
Views: 1,589
|
Forum: Nickey Chevrolet & Bill Thomas Performance
04-07-2021, 02:54 PM
|
Replies: 2
Views: 2,206
|
Forum: Parts/Memorabilia - Sold listings
03-08-2021, 01:14 PM
|
Replies: 3
Views: 2,805
|