Forum: Muscle Car and Corvette Nationals
09-26-2024, 12:21 AM
|
Replies: 29
Views: 3,465
|
Forum: Muscle Car and Corvette Nationals
09-22-2024, 11:12 PM
|
Replies: 29
Views: 3,465
|
Forum: Supercar/Musclecar Discussion
08-16-2024, 07:30 PM
|
Replies: 19
Views: 2,940
If you want to hammer on it with no worries of...
If you want to hammer on it with no worries of what happens to the engine, go with more displacement. I have a 406 small block with AFR's, super victor, and a hydraulic flat tappet in my 67 Camaro...
|
Forum: Technical & Restoration
07-09-2024, 07:26 PM
|
Replies: 5
Views: 824
|
Forum: Garages/shops..
06-27-2024, 01:43 PM
|
Replies: 32
Views: 14,925
|
Forum: Garages/shops..
06-26-2024, 08:33 PM
|
Replies: 32
Views: 14,925
Looks good! I put two 84" fans from home depot...
Looks good! I put two 84" fans from home depot on down rods in my 40x60 shop and they move a considerable amount of air and keep it comfortable. However, once outside temps are above 90 degrees, it...
|
Forum: Preservation forum
06-26-2024, 06:47 PM
|
Replies: 269
Views: 133,012
|
Forum: Mopar
06-19-2024, 02:48 PM
|
Replies: 14
Views: 9,294
|
Forum: Mopar
06-19-2024, 02:37 PM
|
Replies: 14
Views: 9,294
Moving on to the engine, it was evident that it...
Moving on to the engine, it was evident that it was filthy, 50+ years of grime, grease and makeshift repairs, it was leaking from every conceivable orifice, but it ran very well, so I decided to put...
|
Forum: Mopar
06-19-2024, 01:46 PM
|
Replies: 14
Views: 9,294
Continuation from the post yesterday. After...
Continuation from the post yesterday. After examining the internals of the trans, everything looked good, so I cleaned it up, replaced the input shaft and output shaft seals and reinstalled the top...
|
Forum: Mopar
06-18-2024, 09:23 PM
|
Replies: 14
Views: 9,294
Well, I've been hard at work on this Truck for...
Well, I've been hard at work on this Truck for the past few months. I'll add posts as I get time to show the progress. I was able to fix all of the oil leaks, replaced the timing set, cleaned the...
|
Forum: Supercar/Musclecar Discussion
05-06-2024, 06:26 PM
|
Replies: 17
Views: 5,709
|
Forum: Mopar
04-26-2024, 01:30 PM
|
Replies: 14
Views: 9,294
No worries Mitch. I've always liked Mopars as...
No worries Mitch. I've always liked Mopars as well. The truck I'm working on now has been a part of my life since I was about a year old. My dad bought it in the mid 80s and used it for his...
|
Forum: Day 2 stuff-modified cars
04-24-2024, 08:30 PM
|
Replies: 12
Views: 9,761
|
Forum: Yenko Chevrolet
02-14-2024, 08:31 PM
|
Replies: 8
Views: 13,350
|
Forum: Supercar/Musclecar Discussion
10-19-2023, 12:52 PM
|
Replies: 35
Views: 10,019
|
Forum: Technical & Restoration
10-05-2023, 03:41 PM
|
Replies: 42
Views: 16,126
I got the car running again last night but I...
I got the car running again last night but I haven't taken it off of the lift yet. The clutch needs adjusting some more due to the tires still wanting to turn when the pedal is still fully...
|
Forum: Technical & Restoration
10-02-2023, 02:55 PM
|
Replies: 42
Views: 16,126
Thanks for the suggestion. However, I've been...
Thanks for the suggestion. However, I've been running this mount for about 15 years or so now and I have no vibration issues. I checked the pinion angle when I first converted the car to a four...
|
Forum: Technical & Restoration
10-02-2023, 01:49 PM
|
Replies: 42
Views: 16,126
|
Forum: Technical & Restoration
10-01-2023, 08:03 PM
|
Replies: 42
Views: 16,126
|
Forum: Technical & Restoration
09-30-2023, 04:29 PM
|
Replies: 42
Views: 16,126
|
Forum: Technical & Restoration
09-29-2023, 02:41 PM
|
Replies: 42
Views: 16,126
Progress! My crossmember was looking pretty...
Progress! My crossmember was looking pretty rough, so I wire wheeled it, and shot it with some primer and paint to clean it up. I was able to get the flywheel resurfaced and balanced with the...
|
Forum: Technical & Restoration
09-25-2023, 02:10 PM
|
Replies: 42
Views: 16,126
|
Forum: Technical & Restoration
09-18-2023, 05:41 PM
|
Replies: 42
Views: 16,126
I was able to make some more progress on the...
I was able to make some more progress on the Muncie this weekend. The main drive assembly is back in the case, new seals have been installed in the extension housing and it has been reinstalled. ...
|
Forum: Technical & Restoration
09-12-2023, 03:36 PM
|
Replies: 42
Views: 16,126
I agree, he’s been extremely helpful in this...
I agree, he’s been extremely helpful in this entire process. Couldn’t ask for better or faster customer service. I called and sent some pictures to him, it was immediately diagnosed and he had all...
|